DMG MORI DMF 300|11 Fresadoras de mesa redonda

· General

· Travelling column machine; Control: CELOS with Siemens 840D sl Operate
·

· Working area 1

· Longitudinal
· 3000 mm

· Cross
· 1100 mm

· Vertical
· 1050 mm

· Feed drives:

· Feed rate X / Y / Z
· 42000/42000/42000 mm/min

· Rapid feed X / Y / Z
· 42/42/42 m/min

· NC-swivel head (B-axis)
· Controlled NC-swivel milling head (B-axis) with clamping in position. Continuously positioning NC swivel milling head with integrated motor spindle for 4/5 axes positioning and simultaneous machining. Swivel torque: 3,300 / 2,300 Nm // 2,433 / 1,696 ft

· Dynamic package for DMF 300|11 linear
· Dynamic package for DMF 300|11 linear Linear motor X-axis with 80 m/min // 262.48 ft/min Rapid speed XYZ 80 m/min // 262.48 ft/min Acceleration XYZ 8 m/s² // 26.25 ft/s² Active cooling for Linear motor

· Toolchanger with twin-gripper
· toolchanger with twin-gripper

·
· Type of magazine Chain

·
· Number of tools 40

· Cabine
· Full protection cabin

· Package Mill / Turn 20,000 rpm, HSK-A63
· Package Mill / Turn, 20,000 rpm HSK-A63 (Only available for Siemens 840D solutionline) NC-Mill-Turn-table d 1,050 mm / 41.3 in (left) C-axis direct drive, speed max. 700 rpm Integrated balancing system Milling spindle power 35/25 kW (40/100% ED) tool hold

· Removable partition wall DMF |11
· Partition wall removable for pendulum machining, 2 working spaces

· Tool magazine 90 places
· Tool magazine 90 places SK40/HSK-A63 Chain type with double gripper

· Coolant tempering for internal coolant 980l
· Coolant tempering for internal coolant unit 980l / 259 gallon: Heating capacity max.: 4 kW / 5.3 hp Cooling capacity max.: 4 kW / 5.3 hp (only in combination with internal coolant unit 980l)

· Oil mist separator (with partition wall)
· Oil and emulsion mist separator system 2 pieces per machine implemented in right and left cabin side wall. mechanical filter system 2x1600 m³/h

· Combi-Tool measuring
· Combi - Tool measuring Blum LaserControl LC52 DIGILOG Laser-System for milling tools 3D-probe for turning tools

· 3D quickSET elevated constructuion
· 3D quickSET Tool kit for control and compensation of the cinematic accuracy of 5 axis machine configurations include additional fixture for elevated construction (only with option touch probe)

· Minimum lubrication external
· Minimum lubrication external for vertical or swivel head

· Double cartridge filter,25 µm
· Double cartridge filter, Finesse of filtration 25 µm (only in combination with internal coolant)

· Inner coolant supply 40Bar/980l
· Internal coolant supply (ICS) with paper type filter 40 Bar/980 l // 580 psi/258.8 gallon inclusive 2 rotating clear window, air purge for linear measuring system, rotary joint for main spindle

· Sensor package i4.0
· Sensor package i4.0: MPC Machine Protection Control SGS Spindle Growth Sensor ICS flow sensor

· Signal lamp 4-colour
· Signal lamp, 4 colours

· Infrared measuring probe PP 600 optical
· Infrared touch Probe type Renishaw PP600 optical (OMP600)

· Door drive for working area doors
· Door drive for working area doors Open / close - activated by two-hand-operation at the control panel Safety sensor technology for prevention of accidents

· Stop block Speedmaster
· Stop block HSK-A63/SK40/CAT40 for Speedmaster spindle

· Package for tropical climate (dynamic vers.)
· Package for tropical climate DMF(dynamic vers.) for ambient temperature max.50° Celsius: including reinforced active cooling for motor spindle and Linear motor temperature control for hydraulic oil

· ATC (Application Tuning Cycle)
· ATC (Application Tuning Cycle) programmable feed parameter selection for machining task: accuracy/surface/speed

· Operation mode 4
· Operation mode 4 "Process monitoring in the production" Manual intervention with open doors of machining area. Release after check list has been filled in.

· Working plain transformation
· working plain transformation (requirement option electronic angle indication for rotary table)